How it works
A simple, tidy installation
The indoor unit goes high on an inside wall. A single neat pipe run passes through the wall to the outdoor unit — ideally directly behind, which keeps the job quick and the finish clean.
Illustrative only — the unit position and pipe route are agreed with you at the survey.
What you get
Built for UK homes, all year round
Heating as well as cooling
An air-to-air heat pump, so it warms the room in winter as well as cooling it in summer. The manufacturer quotes heating operation down to −20°C outside.
Quiet indoors
The indoor unit goes as low as 22 dB(A) in quiet mode — the quietest of seven fan settings, designed for bedrooms at night.
Sized for everyday rooms
A 3.5 kW-class system suits a typical living room, larger bedroom or home office. We confirm the right size with a heat-load check at survey.
Inverter efficiency
An inverter compressor speeds up and slows down to match demand, rather than switching on and off. Rated A++ for cooling and A+ for heating.
Compact outdoor unit
A small outdoor unit, around 71 cm wide, that fits neatly on a wall bracket or ground stand.
R32 refrigerant
Uses R32, the refrigerant now standard in modern split systems.
Specification
ZERO 3.5 kW split system
| Model | ZERO ZMSA-12HVT-EU (indoor and outdoor unit) |
|---|---|
| Cooling capacity | 3.4 kW (12,000 Btu/h class) |
| Heating capacity | 3.42 kW |
| Seasonal cooling efficiency | SEER 6.1 |
| Seasonal heating efficiency | SCOP 4.0 (average climate) |
| Indoor sound pressure | From 22 dB(A), quiet (mute) mode |
| Outdoor sound power | 62 dB(A) |
| Outdoor operating range | Cooling up to 53°C · heating down to −20°C |
| Typical room size | Approx. 14–22 m² (manufacturer guidance) |
| Maximum pipe run | 25 m |
| Refrigerant | R32, factory-charged 0.52 kg |
| Outdoor unit size | 712 × 459 × 276 mm (W × H × D) |
| Power supply | 220–240 V single phase |
Figures are from the manufacturer's published data. Energy classes are seasonal ErP ratings; the heating class shown is for the average European climate zone. Sizing for your rooms is confirmed with a heat-load check at survey.
The installation
What's included, and what we check at survey
Included as standard
- Indoor and outdoor unit, supplied and fitted
- Outdoor unit mounted on wall brackets or a ground stand
- Standard pipe run, neatly routed and covered in trunking
- Wall core drilled and sealed, condensate drainage
- Electrical connection, tested and certificated by a qualified electrician
- Pressure test, evacuation and commissioning by an F-Gas certified engineer
- A walk-through of the controls before we leave
Confirmed at survey
- Longer pipe runs, or a room away from an outside wall
- Access equipment for high or awkward walls
- Whether a new electrical circuit is needed
- Outdoor unit position, noise and neighbours
- Any planning considerations for your property
You get a fixed written quote after the survey, so anything extra is agreed before any work starts.
Questions
Common questions
Is 3.5 kW the right size for my room?
For most living rooms, larger bedrooms and home offices, yes. Very sunny rooms, conservatories and open-plan spaces may need more. We check with a heat-load calculation before we quote, so you don't end up with a unit that's too small or too big.
Can I add more rooms later?
A single-split serves one room. If you're likely to want two rooms, a two-room multi-split is often neater and better value — see our two-room system.
How long does the installation take?
A straightforward single-room install is usually completed in a day. We'll give you a firm timescale with your quote.
Will I need planning permission?
Many installations don't, but it depends on your property and where the outdoor unit goes. We check this, along with noise and neighbouring homes, before we quote.
Get a quote
Is a single-room system right for you?
Send us your postcode and a few photos and we'll tell you. Early enquiries get first choice of install dates from early 2027.